Chevrolet Cruze Bolt Pattern, Wheel & Tire Sizes
TL;DR
US-market Cruze sedans (2009-2019, both generations) share a 5x105 mm, 5-lug bolt pattern with roughly 56.5-56.6 mm center bore on gasoline engines; factory wheels range from 15 to 18 inches depending on trim and year.
Bolt pattern by generation
Wheel-fitment databases (Wheel-Size.com and cross-referenced bolt-pattern charts) show that the first-generation Chevrolet Cruze (J300, model years 2009-2015) and the second-generation Cruze (2016-2019 in North America, chassis code J400/D2LC) both use a 5x105 mm bolt pattern on gasoline-engine cars, with a stud thread of M12 x 1.5. This makes the pattern consistent across the two US-sold generations, which is unusual and worth double-checking on your own vehicle rather than assuming.
Center bore
Gasoline-engine Cruze models are consistently listed with a center bore of about 56.5-56.6 mm. Some overseas diesel-engine variants of the Cruze have been reported elsewhere with a different bolt pattern (5x115 mm) and a larger center bore (around 70.2 mm), but this could not be corroborated across multiple independent sources for this rewrite, so treat any diesel-specific figure as unverified until you check your own car.
Why this matters
Fitting aftermarket wheels with the wrong center bore leaves the wheel supported only by the lug bolts, which can cause vibration or long-term stud damage. Always ask for or install hub-centric rings if the aftermarket wheel's bore is larger than your hub.
Stock wheel and tire sizes
| Generation / years | Bolt pattern | Centre bore | Stud thread | Stock wheel sizes | Common tire sizes |
|---|---|---|---|---|---|
| 1st gen (J300), 2009-2011 | 5x105 mm | ~56.6 mm (gas) | M12 x 1.5 | 6.5Jx16 ET39, 7Jx17 ET42 | 205/60R16, 215/50R17 |
| 1st gen facelift (J300), 2012-2015 | 5x105 mm | ~56.6 mm (gas) | M12 x 1.5 | 6.5Jx16 ET39, 7Jx17/7.5Jx17 ET42, 7.5Jx18 ET42 | 205/60R16, 215/55R17, 225/50R17, 225/45R18 |
| 2nd gen (J400/D2LC), 2016-2019 (US) | 5x105 mm | ~56.6 mm (gas) | M12 x 1.5 | 6Jx15 ET41, 7Jx16 ET41, 7.5Jx17 ET44 | 195/65R15, 205/55R16, 225/45R17 |
| Export/overseas diesel variants (both gens) | Reported as 5x115 mm in some sources (not independently confirmed here) | Reported as ~70.2 mm (not independently confirmed here) | Not confirmed | Varies by market | Varies by market |
Always confirm on your own vehicle
Bolt patterns, center bore, and recommended wheel/tire sizes can vary by market, trim, and even mid-generation running changes. Before buying wheels or tires, verify the exact numbers for your specific car using the driver's door jamb placard, the tire and loading information label (also sometimes on the fuel filler flap), your owner's manual, the markings stamped on your current wheels and tires, and if needed the manufacturer's towing/trailering guide which often lists wheel and tire specs by trim.
Summary
| Bolt pattern (gas, both US gens) | 5x105 mm (5x4.13 in) |
|---|---|
| Center bore (gas engines) | ~56.5-56.6 mm |
| Stud thread | M12 x 1.5 |
| Factory wheel size range | 15 in to 18 in |
| Common factory tire sizes | 195/65R15 to 225/45R18 |
| Diesel/export pattern (unverified) | Reported 5x115 mm in some sources, not confirmed here |
| Where to verify your car | Door placard, owner's manual, tire sidewall markings |
Full diagnostics
For the complete step-by-step diagnostic and repair guide, see Chevrolet Cruze: Common Problems, Fault Codes & Repairs.
Frequently asked questions
Is the bolt pattern the same on every Chevrolet Cruze generation?
For the two generations sold in the US (2009-2015 first-gen J300 and 2016-2019 second-gen), gasoline models consistently show a 5x105 mm bolt pattern in wheel-fitment databases. Some overseas diesel variants are reported with a different pattern in a few sources, but that could not be independently confirmed for this article, so check your own vehicle's placard or wheel markings if you have a diesel or export-market car.
What center bore does the Chevy Cruze use?
Gasoline-engine Cruze models are consistently listed with a center bore of about 56.5 to 56.6 mm across both US generations. If you install aftermarket wheels with a larger bore, use hub-centric rings to keep the wheel properly centered on the hub.
What size are the factory wheels on a Chevy Cruze?
Factory wheel sizes ranged from 15-inch to 18-inch depending on trim and model year, for example 6.5Jx16 ET39 with 205/60R16 tires on early first-gen cars, up to 7.5Jx18 with 225/45R18 tires on higher trims, and 6Jx15 to 7.5Jx17 wheels on second-generation (2016-2019) models.
Where can I find the exact wheel specs for my specific Cruze?
Check the placard on the driver's door jamb, the tire and loading information label, your owner's manual, the markings stamped into your current wheels and tires, or the manufacturer's towing/trailering guide, since these reflect the exact configuration of your car rather than a generic average.