Toyota Highlander Bolt Pattern, Wheel & Tire Sizes
TL;DR
5x114.3 (5 lugs, 114.3 mm) and a 60.1 mm centre bore hold across the four US generations (XU20, XU40, XU50, XU70); wheel size ranges from 16 in on early base models to 20 in on newer top trims.
Bolt pattern and centre bore
Across the four North American generations that wheel-fitment databases (wheel-size.com derived data cross-checked with tirewheelguide.com) document, the Highlander has consistently used a 5x114.3 mm bolt pattern (5 lugs on a 114.3 mm circle) with a 60.1 mm centre bore and M12x1.5 wheel stud thread. This was verified separately for the 2001-2007 (XU20), 2008-2013 (XU40), 2014-2019 (XU50) and 2020-present (XU70) generations rather than assumed to carry over.
Wheel and tire sizes by generation
Wheel diameter and tire size grew with each redesign and vary by trim within a generation (base trims typically get a smaller, taller-sidewall tire; top trims get a larger-diameter wheel with a lower-profile tire). The table below lists the stock combinations found in generation-specific fitment data.
| Generation / years | Bolt pattern | Centre bore | Stud thread | Stock wheel sizes | Common tire sizes |
|---|---|---|---|---|---|
| XU20 (2001-2007) | 5x114.3 | 60.1 mm | M12x1.5 | 16x6.5, 17x6.5 | 225/70R16, 225/65R17 |
| XU40 (2008-2013) | 5x114.3 | 60.1 mm | M12x1.5 | 17x7.5, 19x7.5 | 245/65R17, 245/55R19 |
| XU50 (2014-2019) | 5x114.3 | 60.1 mm | M12x1.5 | 18x7.5, 19x7.5 | 245/60R18, 245/55R19 |
| XU70 (2020-present) | 5x114.3 | 60.1 mm | M12x1.5 | 18x7.5, 20x7.5 | 245/60R18, 235/55R20 |
Lug nut torque
We could not corroborate a single torque figure across independent sources for every Highlander generation, so no number is stated here. Toyota's own spec (found on the driver door jamb sticker or in the owner's manual torque chart) is the only figure you should use when reinstalling wheels.
Always confirm on your own vehicle
Because trim-level wheel sizes and even minor mid-cycle running changes can shift a spec, always confirm your exact numbers before ordering wheels or tires using:
- The driver's door jamb placard (tire size and pressure)
- The owner's manual (torque specs, wheel/tire options)
- The markings stamped into your current wheel and tire sidewall
- Toyota's manufacturer wheel/towing guide for your exact model year and trim
Summary
| Bolt pattern (all gens) | 5x114.3 mm |
|---|---|
| Centre bore (all gens) | 60.1 mm |
| Stud thread | M12 x 1.5 |
| XU20 (2001-2007) wheels | 16x6.5 / 17x6.5 in |
| XU40 (2008-2013) wheels | 17x7.5 / 19x7.5 in |
| XU50 (2014-2019) wheels | 18x7.5 / 19x7.5 in |
| XU70 (2020-present) wheels | 18x7.5 / 20x7.5 in |
Full diagnostics
For the complete step-by-step diagnostic and repair guide, see Toyota Highlander: Common Problems, Fault Codes & Repairs.
Frequently asked questions
Does the Toyota Highlander bolt pattern change between generations?
No - the bolt pattern has stayed 5x114.3 mm (5 lugs, 114.3 mm circle) across the XU20, XU40, XU50 and XU70 generations sold in North America, based on generation-specific fitment data. Always confirm with your own door placard or a wheel shop before buying aftermarket wheels, since some markets or special trims can differ.
What is the centre bore on a Toyota Highlander?
Generation-specific fitment data lists a 60.1 mm centre bore for the XU20 through XU70 Highlander generations. If you are fitting an aftermarket wheel with a different (usually larger) bore, use a hub-centric ring to take up the gap rather than relying on the lug nuts to centre the wheel.
What tire size came standard on my Highlander?
It depends on generation and trim: 2001-2007 base models ran roughly 225/70R16 or 225/65R17; 2008-2013 ran 245/65R17 or 245/55R19; 2014-2019 ran 245/60R18 or 245/55R19; and 2020-present models run 245/60R18 (L/LE/XLE) or 235/55R20 (Limited/Platinum). Check your door placard for the exact size and recommended pressure for your specific build.
What torque should I use on Highlander lug nuts?
We did not find a torque figure that independent sources agreed on for every generation, so we are not stating one here. Use the torque value printed on your driver's door jamb sticker or in your owner's manual, and torque in a star pattern with a calibrated torque wrench.