Honda HR-V Bolt Pattern, Wheel & Tire Sizes
TL;DR
5x114.3 (5x4.5) bolt pattern, 64.1 mm center bore, M12x1.5 studs - this combination checked out on every HR-V generation we looked up, though wheel and tire sizes vary by trim, market and model year.
Honda HR-V wheel bolt pattern and center bore
The HR-V has been built on several different platforms since 1999 (the original GH-generation mini-SUV, the 2015-2023 first-generation RU global model, the Europe-market RV introduced in 2021, and the current RZ generation sold in the US, Canada, Mexico and China since 2023). Fitment data we pulled per generation shows the same bolt pattern, center bore and stud thread across all of them: 5x114.3 (5x4.5), a 64.1 mm center bore, and M12x1.5 wheel studs. Some fitment databases also list a factory tightening torque of about 108 Nm (80 lb-ft), but treat that as a starting reference and always check your own owner's manual, since torque specs can vary by wheel material and year.
Wheel and tire sizes differ by generation and trim
Even though the pattern stays the same, the stock wheel diameter and tire size change a lot depending on generation, trim level and market. Do not assume your specific trim matches another year just because the bolt pattern matches.
Where to confirm your exact vehicle's specs
Bolt pattern rarely changes, but wheel size, offset and tire size do change by trim and region, so always confirm using one of these sources for your specific vehicle:
- The driver's door jamb placard (also lists the recommended tire size and cold pressure)
- Markings stamped on the back of the wheel itself (size, offset and sometimes bolt pattern)
- The sidewall of your current tires
- Honda's owner's manual for your model year and trim
| Generation / years | Bolt pattern | Centre bore | Stud thread | Stock wheel sizes | Common tire sizes |
|---|---|---|---|---|---|
| GH, 1999-2006 (original global HR-V) | 5x114.3 | 64.1 mm | M12x1.5 | 15-16 in | 195/70R15, 205/60R16 |
| RU / RU Facelift, 2015-2023 (first-gen global/US HR-V) | 5x114.3 | 64.1 mm | M12x1.5 | 16-18 in | 215/60R16, 215/55R17, 225/45R18 or 225/50R18 (varies by market) |
| RV, 2021-present (Europe/other markets, Jazz-based design) | 5x114.3 | 64.1 mm | M12x1.5 | 17-18 in | 215/60R17, 225/50R18 |
| RZ / RZ China, 2023-present (US, Canada, Mexico, China) | 5x114.3 | 64.1 mm | M12x1.5 | 17-18 in | 215/60R17, 225/55R18 |
Buying aftermarket wheels
Because the pattern and bore are consistent across HR-V generations, wheels sized correctly for one generation will physically bolt on to another - but that does not guarantee correct fitment. Offset (ET) and wheel width still need to suit your specific trim to avoid rubbing on struts, fender liners or brake calipers, so match offset to your generation and, ideally, your exact trim.
Summary
| Bolt pattern (all verified generations) | 5x114.3 (5x4.5) |
|---|---|
| Centre bore | 64.1 mm |
| Stud thread | M12 x 1.5 |
| Reported factory torque (verify in your manual) | ~108 Nm / 80 lb-ft |
| Stock wheel diameter range | 15-18 in depending on generation/trim |
| Common tire sizes | 195/70R15 to 225/55R18 depending on generation/trim |
Full diagnostics
For the complete step-by-step diagnostic and repair guide, see Honda HR-V: Common Problems, Fault Codes & Repairs.
Frequently asked questions
What is the bolt pattern on a Honda HR-V?
Every HR-V generation we checked - the 1999-2006 original, the 2015-2023 first generation, the Europe-market RV, and the current 2023+ RZ generation - uses a 5x114.3 (5x4.5) bolt pattern. This is one of the more consistent Honda platforms for fitment, but always double-check your own wheel or door placard before ordering.
Is the center bore the same on every HR-V?
Yes, based on the generations we verified, the HR-V uses a 64.1 mm center bore throughout. If you're fitting aftermarket wheels with a larger center bore, you'll need a hub-centric ring to take up the gap; if the aftermarket bore is smaller than 64.1 mm, the wheel will not fit without machining.
What size lug nuts or studs does the HR-V use?
M12x1.5 wheel studs are used across the generations we checked. Some fitment databases list a factory torque spec around 108 Nm (80 lb-ft), but confirm the torque value in your specific owner's manual since it can vary by wheel type and model year.
Can I put wheels from one HR-V generation on another?
The bolt pattern and center bore match across generations, so a wheel that fits one generation will physically bolt on to another. However, offset and width still matter for clearance around the strut, brake caliper and fender liner, so check offset compatibility for your specific generation and trim before buying.