Hyundai Creta Bolt Pattern, Wheel & Tire Sizes
TL;DR
Brazil-market Creta (gen 1 GS/GC and gen 2 SU2) uses a 5x114.3 bolt pattern, 67.1 mm centre bore and M12x1.5 studs, with factory wheels ranging 16 to 18 inches depending on trim.
Which Creta this page covers
This page focuses on the Brazil / Latin-American market Hyundai Creta, sold there since 2017 as a locally built first generation (GS/GC, later facelifted) and, from 2021, as the globally-sourced second generation (SU2). Figures below come from wheel-fitment databases cross-checked page by page for each generation listing; where a number could not be corroborated it has been left out rather than guessed.
Bolt pattern, centre bore and stud thread
Across every Creta generation and facelift checked for the Brazilian/LatAm market, the wheel bolt pattern was consistently 5x114.3 (5x4.5 inch), with a 67.1 mm centre bore and M12x1.5 stud thread. Because this held for the original GS, the GS facelift, and the SU2 generation, it is reasonable to treat it as stable for the Brazil-market Creta line - but always confirm on your own vehicle before ordering aftermarket wheels, since running changes or region-specific suppliers can occasionally differ.
Factory wheel and tire sizes
Factory wheel and tire sizes vary by trim and engine, growing from a 16-inch steel/alloy wheel on base trims up to 18-inch alloys on top trims.
| Generation / years | Bolt pattern | Centre bore | Stud thread | Stock wheel sizes | Common tire sizes |
|---|---|---|---|---|---|
| Creta I (GS), Brazil, 2017-2021 | 5x114.3 | 67.1 mm | M12x1.5 | 6Jx16 ET43 / 6.5Jx17 ET49 | 205/65R16 95H, 215/60R17 96H |
| Creta I (GS) facelift, Brazil/LatAm, 2021-2024 | 5x114.3 | 67.1 mm | M12x1.5 | 6Jx16 ET43 / 6.5Jx17 ET49 / 6.5Jx18 ET49 | 205/65R16 95H, 215/60R17 96H, 215/55R18 95H |
| Creta II (SU2), Brazil, since 2021 | 5x114.3 | 67.1 mm | M12x1.5 | 6Jx16 ET43 up to 7Jx18 ET48 | 205/65R16 95H, 215/60R17 96H, 225/55R17 97H, 215/55R18 95H, 225/50R18 95H |
Always confirm on your specific car
Bolt pattern, centre bore and torque can vary by trim, market batch or a mid-cycle running change that a general database has not caught yet. Before buying wheels, confirm your exact figures from your own vehicle: the driver door placard, the owner's manual, the markings stamped on your current wheels, or a Hyundai dealer parts catalogue referencing your VIN.
Lug nut torque
Wheel-fitment data for the first-generation Creta lists a factory tightening torque around 88-107 Nm (65-79 lbf-ft). Torque can differ by wheel material (steel vs alloy) and generation, so treat this as a reference point and verify against your owner's manual before tightening lug nuts.
Summary
| Primary market covered | Brazil / Latin America |
|---|---|
| Bolt pattern (all generations checked) | 5x114.3 (5x4.5 in) |
| Centre bore | 67.1 mm |
| Stud thread | M12x1.5 |
| Stock wheel range | 16 in to 18 in |
| Common OE tire sizes | 205/65R16 to 225/50R18 |
| Reference lug torque (gen 1) | 88-107 Nm (65-79 lbf-ft) |
Full diagnostics
For the complete step-by-step diagnostic and repair guide, see Hyundai Creta: Common Problems, Fault Codes & Repairs.
Frequently asked questions
Is the bolt pattern the same on every Creta generation sold in Brazil?
Based on the generation-by-generation data checked (first-generation GS, its facelift, and the second-generation SU2), all use a 5x114.3 (5x4.5 inch) bolt pattern with a 67.1 mm centre bore and M12x1.5 studs. Still, confirm on your own car since running changes can occasionally alter fitment mid-generation.
What size are the factory wheels on the Brazilian Creta?
Factory wheels range from 16-inch (6Jx16, tires around 205/65R16) on entry trims up to 17 or 18-inch alloys (up to 7Jx18, tires such as 215/55R18 or 225/50R18) on higher trims, depending on generation and engine.
Will aftermarket wheels with 5x114.3 fit any Creta?
A 5x114.3 pattern and 67.1 mm centre bore wheel should physically bolt onto the generations covered here, but always double-check offset (ET), load rating and hub-centric fit against your exact trim before purchasing, and have a shop confirm clearance with your brakes and suspension.
Where can I find the exact torque spec for my Creta's lug nuts?
Wheel-fitment references cite roughly 88-107 Nm (65-79 lbf-ft) for the first-generation model, but the authoritative figure for your specific car is in your owner's manual or from your Hyundai dealer, since it can vary by wheel type and generation.