Nissan Rogue Bolt Pattern, Wheel & Tire Sizes
TL;DR
Every generation of the Nissan Rogue uses a 5x114.3 bolt pattern and M12x1.25 lug studs, so wheel fitment is unusually consistent across the model's history - but always confirm the exact tire size for your trim on the tire sidewall or door placard before buying.
Bolt pattern and center bore by generation
The Nissan Rogue has had three US generations: the first-generation Rogue (chassis code S35, 2008-2013, sold as the Rogue Select through 2015), the second generation (T32, 2014-2020), and the current third generation (T33, 2021-present). Multiple wheel-fitment databases agree that all three generations share a 5x114.3 mm (5x4.5 in) bolt pattern and a 66.1 mm hub-centric bore. A minority of listings show 66.5 mm for some second-generation (T32) 17-inch wheel setups, so if you are machining or shimming a centric ring for a T32 wheel, measure your factory wheel's bore before ordering.
Wheel studs and lug torque
Lug hardware is M12x1.25 thread with a conical (60-degree) seat across all three generations, using a 21 mm (13/16 in) hex on most factory lug nuts. A commonly cited factory lug torque is around 80 ft-lb (108 Nm), but torque specs can differ slightly by model year and wheel material (steel vs alloy), so confirm the number in your own owner's manual before tightening.
Stock wheel and tire sizes
Early Rogues (S35, 2008-2013) were fitted with 16 or 17-inch steel or alloy wheels depending on trim; exact tire codes vary enough by trim and model year that we recommend reading yours directly off the tire sidewall or door placard rather than relying on a single number here. The second generation (T32, 2014-2020) offered 17, 18, and 19-inch wheels across S/SV/SL/Platinum trims, again with tire sizing that changes by trim and drivetrain (FWD vs AWD). The third generation (T33, 2021-present) is better documented: base S/SV trims commonly ride on 17-inch wheels with 225/65R17 tires, while SL/Platinum trims step up to 18-inch wheels with 235/60R18 tires.
Where to verify your exact fitment
Because trims, model years, and regional packages change tire and wheel sizing even within one generation, always cross-check against your own vehicle before buying wheels or tires.
- The driver's door jamb placard lists the factory tire size and cold inflation pressure for your exact build.
- Your owner's manual lists the factory lug torque and any spare-tire size, which can differ from the road tires.
- The tire sidewall itself shows the current tire size, which may not match the original factory size if it was changed.
- A tire shop's fitment lookup by VIN is the most reliable way to confirm bolt pattern and offset for aftermarket wheels.
| Generation / years | Bolt pattern | Centre bore | Stud thread | Stock wheel sizes | Common tire sizes |
|---|---|---|---|---|---|
| 1st gen S35 (2008-2013, Rogue Select through 2015) | 5x114.3 | 66.1 mm | M12x1.25 | 16-17 in | Varies by trim - check door placard |
| 2nd gen T32 (2014-2020) | 5x114.3 | 66.1 mm (some 17 in listings show 66.5 mm) | M12x1.25 | 17 / 18 / 19 in | Varies by trim and FWD/AWD - check door placard |
| 3rd gen T33 (2021-present) | 5x114.3 | 66.1 mm | M12x1.25 | 17 / 18 in | 225/65R17 (S/SV) or 235/60R18 (SL/Platinum) |
Summary
| Bolt pattern (all gens) | 5x114.3 mm |
|---|---|
| Center bore | 66.1 mm (some T32 listings: 66.5 mm) |
| Wheel stud thread | M12x1.25, conical seat |
| Typical lug torque | ~80 ft-lb / 108 Nm (verify in manual) |
| Stock wheel sizes | 16-19 in depending on generation/trim |
| T33 (2021+) tire sizes | 225/65R17 or 235/60R18 |
| Authoritative source | Driver's door placard and owner's manual |
Full diagnostics
For the complete step-by-step diagnostic and repair guide, see Nissan Rogue: Common Problems, Fault Codes & Repairs.
Frequently asked questions
Do all Nissan Rogue generations use the same bolt pattern?
Yes - the 2008-2013 (S35), 2014-2020 (T32), and 2021-present (T33) generations all use a 5x114.3 mm bolt pattern, which is unusually consistent for a model spanning three generations. This means many aftermarket wheels designed for one generation will bolt up to another, though you should still confirm offset and center bore separately since those can differ by trim.
What center bore does the Nissan Rogue use?
Most fitment databases list 66.1 mm as the hub-centric bore across all three generations, though a small number of listings for second-generation (2014-2020) 17-inch wheel setups show 66.5 mm. If you're using hub-centric rings on aftermarket wheels, measure your factory wheel's bore directly rather than assuming one figure.
What thread size are the wheel studs on a Nissan Rogue?
The Rogue uses M12x1.25 wheel studs with a conical (60-degree) seat across all three generations, typically torqued with a 21 mm (13/16 in) lug wrench socket. A commonly cited factory torque spec is about 80 ft-lb (108 Nm), but always verify against your own owner's manual since it can vary slightly by year and wheel material.
What size are the stock wheels and tires on my Rogue?
It depends on generation and trim: first-generation cars (2008-2013) ran 16-17 inch wheels, second-generation cars (2014-2020) offered 17/18/19 inch wheels, and third-generation cars (2021-present) commonly use 225/65R17 tires on S/SV trims or 235/60R18 on SL/Platinum trims. For your exact car, check the tire size printed on the driver's door jamb placard or on the tire sidewall itself.