Renault Duster Bolt Pattern, Wheel & Tire Sizes
TL;DR
Brazil/Latin America Duster Gen 1 and Gen 2 use a 5x114.3 bolt pattern, 66.1 mm center bore and M12x1.50 studs; Gen 3 specs are unverified here - confirm on your own car.
Which Duster is this about
This page focuses on the Brazil / Latin American market Renault Duster, sold there since 2011. Two generations are covered with reasonable confidence: the first generation (locally called G1, roughly 2011-2020) and the second generation (G2, roughly 2020-2026, also known internationally as the HM). A newer, third-generation Duster built on Renault's global small-car platform has begun reaching some markets from around 2025; its wheel bolt pattern could not be confirmed against multiple credible sources at the time this page was written, so that figure is intentionally left out below rather than guessed.
Bolt pattern and center bore
For the Brazilian G1 and G2 Duster, wheel-fitment retailer data consistently lists a 5x114.3 mm bolt pattern (5 studs on a 114.3 mm circle), a 66.1 mm center bore, and M12x1.50 wheel studs. Offset (ET) on factory and common aftermarket wheels runs roughly ET40 to ET50, depending on wheel width and trim.
Wheel and tire sizes
Factory wheels on the Brazilian Duster commonly range from 16 to 17 inches, paired with tire sizes such as 215/65 R16, 235/65 R16 (some trims), and 215/60 R17, depending on model year and trim level (Zen, Intense, Iconic, and similar).
Always confirm on your own vehicle
Bolt pattern, center bore and recommended tire sizes can vary by trim, market and production date even within one generation. Before buying wheels or tires, confirm the exact figures for your specific car using one of these authoritative sources:
- The driver's door jamb placard (tire size, recommended pressure, sometimes rim size)
- The owner's manual supplied with the vehicle
- The markings stamped on your current wheels and tire sidewalls
- A Renault dealer parts/service department, which can look up the exact configuration by VIN
| Generation / years | Bolt pattern | Centre bore | Stud thread | Stock wheel sizes | Common tire sizes |
|---|---|---|---|---|---|
| Duster I / G1 (Brazil, approx. 2011-2020) | 5x114.3 | 66.1 mm | M12x1.50 | 16 in (6.5J-7J), ET approx. 40-50 | 215/65 R16 |
| Duster II / G2, HM (Brazil, approx. 2020-2026) | 5x114.3 | 66.1 mm | M12x1.50 | 16-17 in, ET approx. 38-50 | 215/65 R16, 215/60 R17, 235/65 R16 (some trims) |
| Duster III, new global platform (from approx. 2025, market-dependent) | Not confirmed here - varies by market/trim; verify on your own car | Not confirmed here | Not confirmed here | 17-18 in reported on some trims (unverified) | Check door placard or manual |
Summary
| Market covered | Brazil / Latin America (primary) |
|---|---|
| Gen 1 (approx. 2011-2020) bolt pattern | 5x114.3 |
| Gen 2 / HM (approx. 2020-2026) bolt pattern | 5x114.3 |
| Center bore (Gen 1 and Gen 2) | 66.1 mm |
| Stud thread (Gen 1 and Gen 2) | M12x1.50 |
| Common tire sizes | 215/65 R16, 215/60 R17, 235/65 R16 |
| Gen 3 (new platform, from approx. 2025) | Not confirmed - verify on your own vehicle |
Full diagnostics
For the complete step-by-step diagnostic and repair guide, see Renault Duster: Common Problems, Fault Codes & Repairs.
Frequently asked questions
Is the bolt pattern the same on every Renault Duster generation?
No - do not assume that. For the Brazilian Gen 1 (2011-2020) and Gen 2 (2020-2026) Duster, retailer wheel-fitment data agrees on 5x114.3 with a 66.1 mm center bore. The newer third-generation Duster (from around 2025, built on Renault's global small-car platform) is a different design, and its bolt pattern could not be confirmed from credible sources here, so treat it as unverified until you check your own vehicle.
What center bore and stud thread does the Duster use?
For the Brazil-market Gen 1 and Gen 2 Duster, the center bore is 66.1 mm and the wheel studs are M12x1.50, according to wheel-fitment retailer data. Aftermarket wheels with a larger bore opening can use a hub-centric ring to fit safely; wheels with a smaller bore than 66.1 mm will not fit.
What tire sizes come on the Duster from the factory?
Brazilian-market Dusters have most commonly shipped with 215/65 R16 tires, with 215/60 R17 and 235/65 R16 also used on certain trims and model years. Your exact factory size is printed on the driver's door jamb placard and in the owner's manual - use that over any general list.
Where can I find the exact specs for my specific Duster?
The most reliable source is your own car: check the placard on the driver's door jamb (tire size and pressure), the owner's manual (wheel and tire specifications), the markings on your current wheels and tires, and, if unsure, a Renault dealer who can look up your exact build by VIN.