Toyota Camry Bolt Pattern, Wheel & Tire Sizes
TL;DR
Toyota Camry sedans from 2007 onward share a 5x114.3 bolt pattern, 60.1 mm centre bore and M12x1.5 studs; wheel size and tire size depend on the trim (16-19 inch rims).
Toyota Camry wheel and bolt pattern overview
The Toyota Camry sedan has used the same core wheel mounting hardware for several generations, but exact stock wheel and tire sizes shift with trim level, facelift, and market. The figures below come from wheel-fitment databases (wheel-size.com, wheelfitment.eu) cross-checked against aftermarket wheel listings for the 2018-2024 SE trim. Always confirm the pattern and bore stamped or listed for your exact car before buying wheels.
What stayed consistent
- Bolt pattern: 5x114.3 mm (5 lugs, 114.3 mm circle) - corroborated across the XV40, XV50 and XV70 generations by independent fitment references.
- Centre bore: 60.1 mm - confirmed for the XV40 (2001-2011 data) and for XV70 SE aftermarket wheel listings (2018-2024); commonly cited as unchanged across generations.
- Stud thread: M12x1.5 - confirmed for the XV40; widely reported as the same across later generations, but was not independently re-verified for every XV50/XV70 trim in this research.
What varies
Stock wheel diameter (16 to 19 inches) and tire size change by trim, engine and facelift year - see the table. Lug nut torque is commonly cited around 103 Nm (76 lb-ft), though at least one source lists 110 Nm (81 lb-ft) for the XV40 generation, so torque figures vary by source and you should use the value in your own owner's manual.
| Generation / years | Bolt pattern | Centre bore | Stud thread | Stock wheel sizes | Common tire sizes |
|---|---|---|---|---|---|
| XV40 (2007-2011) | 5x114.3 | 60.1 mm | M12x1.5 | 16-18 in | 215/60R16, 215/55R17, 225/45R18 |
| XV50 (2012-2017, incl. 2015 facelift) | 5x114.3 | 60.1 mm (widely reported, not independently re-verified for this generation) | M12x1.5 (widely reported) | 16-18 in | 205/65R16, 215/55R17, 225/45R18 |
| XV70 (2018-2024, incl. 2020 facelift) | 5x114.3 | 60.1 mm | M12x1.5 (widely reported) | 16-19 in | 205/65R16, 215/55R17, 235/45R18, 235/40R19 |
Where to verify your own car
Wheel specs can differ by market and option package even within one model year. Before buying wheels or tires, check the driver's-door placard (inside the door jamb), the factory tire/wheel markings on your current wheels, and your owner's manual, which lists the exact bolt pattern, centre bore, torque and approved wheel/tire sizes for your specific build.
Summary
| Bolt pattern (all gens covered) | 5x114.3 mm |
|---|---|
| Centre bore | 60.1 mm |
| Stud thread | M12x1.5 |
| XV40 (2007-2011) wheel sizes | 16-18 in |
| XV50 (2012-2017) wheel sizes | 16-18 in |
| XV70 (2018-2024) wheel sizes | 16-19 in |
| Lug torque (varies by source) | 103-110 Nm (76-81 lb-ft) |
Full diagnostics
For the complete step-by-step diagnostic and repair guide, see Toyota Camry: Common Problems, Fault Codes & Repairs.
Frequently asked questions
Is the Toyota Camry bolt pattern the same on every generation?
The 5x114.3 mm bolt pattern is corroborated across the XV40 (2007-2011), XV50 (2012-2017) and XV70 (2018-2024) generations by independent fitment databases, so it has been consistent through this modern era of the Camry. Older Camry generations before the 2000s used different patterns, so if you have an older car, verify separately rather than assuming 5x114.3.
What is the Toyota Camry centre bore size?
60.1 mm is the centre bore figure confirmed for the XV40 (2007-2011) generation and for current XV70 (2018-2024) SE aftermarket wheels, and it is commonly reported as unchanged across the generations in between. If you are fitting aftermarket wheels with a larger bore, use hub-centric rings to avoid vibration.
Will any 18-inch wheel fit my Camry?
Not necessarily. The bolt pattern (5x114.3) and centre bore (60.1 mm) must match, and the offset needs to keep the wheel from rubbing the fender or suspension - stock offsets for 18-inch Camry wheels have ranged around ET40 to ET50 depending on generation and trim. Check your specific model year's stock offset before ordering aftermarket wheels.
What torque should I use for Camry lug nuts?
Sources vary: some references cite 103 Nm (76 lb-ft) as the common Camry lug nut torque, while at least one fitment database lists 110 Nm (81 lb-ft) for the XV40 generation. Because this figure can differ by trim and year, use the torque value printed in your own owner's manual rather than a generic number.