Toyota Tundra Oil Capacity & Oil Type
TL;DR
Oil capacity and viscosity vary a lot across Tundra generations - from 4.8 quarts on the early 4.0L V6 to 8.5 quarts on the 5.7L V8, and 7.7 quarts on the newest twin-turbo V6. Confirm your engine code before topping off.
Oil capacity depends entirely on which engine you have
Toyota Tundra has been built across three generations with several completely different engine families, so there is no single correct oil capacity for the truck. The number that matters is tied to the engine code, which is stamped on the engine block and also listed in your owner's manual and on many underhood emissions labels.
Capacity and viscosity by engine
| Engine code / years | Capacity with filter (L / US qt) | Viscosity |
|---|---|---|
| 1GR-FE 4.0L V6 (2007-2009) | 4.5 L / 4.8 qt | SAE 5W-30 |
| 2UZ-FE 4.7L V8 (2007-2009) | 6.2 L / 6.6 qt | SAE 5W-30 |
| 3UR-FE 5.7L V8 (2007-2009) | 7.0 L / 7.4 qt | SAE 5W-20 or 0W-20 |
| 3UR-FE 5.7L V8 (2010-2021) | 8.0 L / 8.5 qt | SAE 0W-20 |
| 1UR-FE 4.6L V8 (2010-2017) | 7.5 L / 7.9 qt | SAE 0W-20 |
| V35A-FTS 3.5L twin-turbo V6, incl. i-FORCE MAX hybrid (2022-present) | 7.3 L / 7.7 qt | SAE 0W-20 |
Why the 2007-2009 5.7L figure looks low
The early 3UR-FE (2007-2009) spec of roughly 7.4 quarts is noticeably lower than the 8.5-quart figure widely reported for 2010 and later trucks with the same engine code. Some service references disagree on exactly when the change took effect, so if your truck is a 2009 or 2010 model year, verify the capacity on your own dipstick fill procedure or dealer service ticket rather than assuming either number.
Where to confirm your exact numbers
Before you buy oil, check these sources for your specific truck:
- The driver's door jamb placard, which sometimes lists fluid specs alongside tire pressure
- The oil filler cap, which is usually stamped with the required viscosity grade
- Your owner's manual, which lists exact capacity for your engine code
- A dealer parts/service lookup by VIN, which is the most reliable way to match your exact engine build
First-generation Tundra (2000-2006)
The original Tundra offered a 3.4L V6 (5VZ-FE) and a 4.7L V8 (2UZ-FE). Reliable, consistent capacity figures for these older engines were not available across our sources for this review, so rather than guess, check your owner's manual or a dealer parts lookup for the exact number on these earlier trucks.
Summary
| 1GR-FE 4.0L V6 (2007-2009) | 4.5 L / 4.8 qt, 5W-30 |
|---|---|
| 2UZ-FE 4.7L V8 (2007-2009) | 6.2 L / 6.6 qt, 5W-30 |
| 3UR-FE 5.7L V8 (2007-2009) | 7.0 L / 7.4 qt, 5W-20/0W-20 |
| 3UR-FE 5.7L V8 (2010-2021) | 8.0 L / 8.5 qt, 0W-20 |
| 1UR-FE 4.6L V8 (2010-2017) | 7.5 L / 7.9 qt, 0W-20 |
| V35A-FTS 3.5L twin-turbo V6 (2022-present) | 7.3 L / 7.7 qt, 0W-20 |
Full diagnostics
For the complete step-by-step diagnostic and repair guide, see Toyota Tundra: Common Problems, Fault Codes & Repairs.
Frequently asked questions
How much oil does a 5.7L Toyota Tundra take?
For 2010-2021 trucks with the 3UR-FE 5.7L V8, expect about 8.5 US quarts (8.0 liters) with a filter change, using SAE 0W-20. Earlier 2007-2009 5.7L trucks are commonly listed closer to 7.4 quarts, so confirm your build year before buying oil.
What oil viscosity does the new turbo V6 Tundra use?
The 2022-present 3.5L twin-turbo V6 (engine code V35A-FTS), including the i-FORCE MAX hybrid version, uses SAE 0W-20 and holds about 7.7 US quarts (7.3 liters) with a filter change.
Does the Tundra's oil capacity change between trims of the same year?
No, within a given model year the capacity is set by the engine, not the trim level. A SR5, Limited, and Platinum with the same engine code take the same amount of oil; only the engine choice changes the figure.
Where can I find the exact oil capacity for my specific Tundra?
Check your owner's manual under maintenance specifications, look at the oil filler cap for viscosity, or ask a Toyota parts department to look up your VIN, which ties directly to your exact engine code and factory fill specification.